PA66 美国杜邦 103FHS 热稳定 阻燃 电气应用 汽车应用 脱模剂

聚酰胺(PA，俗称尼龙)是美国DuPont公司最先开发用于纤维的树脂，于1939年实现工业化。20世纪50年代开始开发和生产注塑制品，以取代金属满足下游工业制品轻量化、降低成本的要求。PA具有良好的综合性能，包括力学性能、耐热性、耐磨损性、耐化学药品性和自润滑性，且摩擦系数低，有一定的阻燃性，易于加工，适于用玻璃纤维和其它填料填充增强改性，提高性能和扩大应用范围。PA的品种繁多，有PA6、PA66、PAll、PAl2、PA46、PA610、PA612、PAl010等，以及近几年开发的半芳香族尼龙PA6T和特种尼龙等新品种。

PA6又名尼龙6是半透明或不透明乳白色粒子，具有热塑性、轻质、韧性好、耐化学品和耐久性好等特性，一般用于汽车零部件、机械部件、电子电器产品、工程配件等产品。手机：13712770966

直线：0769-82339006

传真：0769-82239009

PA66（聚酰胺66或尼龙66），同PA6相比，PA66更广泛应用于汽车工业、仪器壳体以及其它需要有抗冲击性和高强度要求的产品。

PA66注塑工艺

干燥处理：如果加工前材料是密封的，那么就没有必要干燥。然而，如果储存容器被打开，那么建议在85℃的热空气中干燥处理。如果湿度大于0.2%，还需要进行105℃，12小时的真空干燥。

熔化温度：260~290℃。对玻璃添加剂的产品为275~280℃。熔化温度应避免高于300℃。 模具温度：建议80℃。模具温度将影响结晶度，而结晶度将影响产品的物理特性。对于薄壁塑件，如果使用低于40℃的模具温度，则塑件的结晶度将随着时间而变化，为了保持塑件的几何稳定性，需要进行退火处理。

注射压力：通常在750~1250bar，取决于材料和产品设计。

注射速度：高速（对于增强型材料应稍低一些）。 流道和浇口：由于PA66的凝固时间很短，因此浇口的位置非常重要。浇口孔径不要小于0.5t（这里t为塑件厚度）。如果使用热流道，浇口尺寸应比使用常规流道小一些，因为热流道能够帮助阻止材料过早凝固。如果用潜入式浇口，浇口的最小直径应当是0.75mm。典型用途 PA66更广泛应用于汽车工业、仪器壳体以及其它需要有抗冲击性和高强度要求的产品。

透明或不透明乳白色结晶形聚合物，具有可塑性。密度1．15g/cm3。熔点252℃。脆化温度-30℃。热分解温度大于350℃。 连续耐热80-120℃,平衡吸水率2．5%。能耐酸、碱、大多数无机盐水溶液、卤代烷、烃类、酯类、酮类等腐蚀。

手机：13712770966

直线：0769-82339006

传真：0769-82239009

Zytel 151 NC010 A PA 612 resin
Zytel 151L NC010 Lubricated, general purpose molding grade
Zytel 153HSL NC010 Lubricated, heat stabilized, extrusion grade
Zytel 157HSL BK010 Lubricated, heat stabilized, improved weather resistant molding/extrusion grade
Zytel 158 NC010 General purpose PA 612 resin suitable for molding and extrusion applications
Zytel 158L NC010 Lubricated, general purpose molding/extrusion grade -- a higher melt viscosity than Zytel 151L NC010
Zytel 159 NC010 High viscosity, extrusion grade
Zytel 77G33HS1L NC010 33% Glass fiber reinforced, heat stabilized polyamide 612 resin for injection molding
Zytel 77G33L BK031 33% Glass fiber reinforced, black polyamide 612 resin for injection molding
Zytel 77G33L NC010 33% Glass fiber reinforced, polyamide 612 resin for injection molding
Zytel 77G43L BK031 43% Glass fiber reinforced, black polyamide 612 resin for injection molding
Zytel 77G43L NC010 43% Glass fiber reinforced polyamide 612 resin for injection molding
Zytel MT409AHS BK010 Medium Toughened, high performance, heat stabilized, black polyamide 66 resin having good stiffness and

improved knit line strength with superior toughness and processability
Zytel MT409AHS NC010 Medium Toughened, high performance, heat stabilized polyamide 66 resin having good stiffness, improved knit

line strength, surface appearance with outstanding processability
Zytel ST800HSL BK152 Heat stablized Super Tough black polyamide 66 resin. It offers outstanding impact resistance, high productivity

and laser markability
Zytel ST801A NC010A Super Tough, high performance, polyamide 66 resin. It is partially UV stabilized and when appropriately colored

offers limited protection to indirect sunlight exposure.
Zytel ST801AHS BK010 Super Tough, high performance, black polyamide 66 resin. It offers outstanding molding performance in injection

molding applications.
Zytel ST801AHS NC010 Super Tough, high performance polyamide 66 resin. It offers outstanding molding performance in injection

molding applications.
Zytel ST801AW BK195 Super Tough, weatherable, easy flow and processing friendly, black polyamide 66 resin for injection molding. It

offers the best resistance to outdoor exposure.
Zytel ST801AW NC010 Super Tough, high performance polyamide 66 resin. It is UV stabilized and when appropriately colored, offers the

best resistance to indirect sunlight in automotive interior applications.
Zytel ST811HS NC010 Rubber modified nylon 6 resin. Very flexible.
Zytel 8018HS BKB085 14% Glass reinforced toughened heat stabilized black nylon 66 resin
Zytel 8018HS NC010 14% Glass reinforced toughened heat stabilized nylon 66 resin
Zytel 80G14A NC010A 14% Glass fiber reinforced, toughened, high flow polyamide 66 resin. It offers outstanding performance in

injection molding applications.
Zytel 80G14AHS BK099 14% Glass fiber reinforced, toughened, high flow, heat stabilized, black polyamide 66 resin. It offers

outstanding performance in injection molding applications.
Zytel 80G14AHS NC010 14% Glass fiber reinforced, toughened, high flow, heat stabilized polyamide 66 resin. It offers outstanding

performance in injection molding applications.
Zytel 80G25HS BK117 25% Glass fiber reinforced, toughened, heat stabilized, black polyamide 66 resin for injection molding
Zytel 80G33HS1L BK104 33% Glass fiber reinforced, heat stabilized black polyamide 66 resin with outstanding impact resistance

developed using DuPont? Super Tough technology
Zytel 80G33HS1L NC010 33% Glass fiber reinforced heat stabilized polyamide 66 resin with outstanding impact resistance developed

using DuPont? Super Tough technology
Zytel 80G33L NC010 33% Glass fiber reinforced polyamide 66 resin with outstanding impact resistance developed using DuPont? Super

Tough technology
Zytel 80G43HS1L BK104 43% Glass fiber reinforced, heat stabilized, black polyamide 66 resin with superior impact resistance
Zytel 84G33 BKB031 33% Glass reinforced toughened black cube blended nylon 66 and nylon 6 comelt resin

我公司长期经营杜邦Zytel系列PA66，货源稳定，质量保证，原厂原包，假一罚十。可提供SGS、ROHS、REACH报告、UL黄卡、COA材质证明、MSDS、FDA、PDF物性表等各项数据，欢迎来电洽谈！

售后服务：我公司承诺七天无理由包退包换，因原料质量问题，退货所产生的运费由我公司承担，让客户买的放心，用的满意。

手机：13712770966

直线：0769-82339006

传真：0769-82239009